Sylvania TV VCR Combo 6313CE User Manual

OWNER’S

MANUAL

COLOR TV/VCR

6313CE (13 inch)

6319CE (19 inch)

19" MODEL ILLUSTRATED

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

If you need additional assistance for set-up or operating after

reading owner’s manual, please call TOLL FREE : 1-800-968-3429.

Or visit our WEB SITE at http://www.SylvaniaConsumerElectronics.com

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding - If an outside antenna or

cable system is connected to the unit, be sure the antenna

or cable system is grounded so as to provide some protec-

tion against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

No. 70, provides information with respect to proper

grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode. (Fig. A)

19.Damage Requiring Service - Unplug this unit from the

wall outlet and refer servicing to qualified service person-

nel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the oper-

ating instructions. Adjust only those controls that are cov-

ered by the operating instructions, as improper adjustment

of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the unit to its normal operation.

14.Lightning - For added protection for this unit receiver dur-

ing a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the unit due to lightning and power-line

surges.

e. If the unit has been dropped or damaged in any way.

f. When the unit exhibits a distinct change in performance,

this indicates a need for service.

15.Power Lines - An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts - When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check - Upon completion of any service or repairs

to this unit, ask the service technician to perform routine

safety checks to determine that the unit is in proper operat-

ing condition.

16.Overloading - Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry - Never push objects of any

kind into this unit through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the unit.

22.Heat - This unit product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

18.Servicing - Do not attempt to service this unit yourself as

opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

- 3 -

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LOCATION

For safe operation and satisfactory performance of

your unit, keep the following in mind when selecting

a place for its installation:

Shield it from direct sunlight and keep it away

from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

Install the unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the unit near strong magnetic fields.

Avoid moving unit to locations where temperature

differences are extreme.

Be sure to unplug the AC power cord from the out-

let before carrying the unit.

Unauthorized recording or use of broadcast televi-

sion programming, video tape, film or other copy-

righted material may violate applicable copyright

laws. We assume no responsibility for the unautho-

rized duplication, use, or other acts which infringe

upon the rights of copyright owners.

•

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

•

RADIO-TV INTERFERENCE

•

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

Do not handle the power cord with wet hands.

•

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

Do not put your fingers or objects into the unit cas-

•

sette holder.

Do not place anything directly on top of the unit.

•

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a tape is played in a unit which has

moisture, it may damage the tape and unit. Therefore

when the condensation occurs inside the unit, turn

the unit on and allow at least 2 hours for the unit to

dry out.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other unit has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 4 -

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .18

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .18

TRACKING ADJUSTMENT . . . . . . . . . . . . . .18

STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .18

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

AVOID THE HAZARDS OF ELECTRICAL

SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4

C SPECIAL PLAYBACK . . . . . . . . . . . . . . . . . .19

RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .19

AUTO REPEAT PLAYBACK . . . . . . . . . . . . .19

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

C TABLE OF CONTENTS . . . . . . . . . . . . . . . . . .5

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6

C SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

ZERO RETURN . . . . . . . . . . . . . . . . . . . . . . .20

PICTURE SEARCH . . . . . . . . . . . . . . . . . . . .20

TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . .20

C OPERATING CONTROLS AND FUNCTIONS 7

INSTALLING THE BATTERIES . . . . . . . . . . .8

C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .21

REAL TIME TAPE COUNTER . . . . . . . . . . . .21

AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .21

C PREPARATION FOR USE . . . . . . . . . . . . . . . .9

ANTENNA/CABLE CONNECTIONS . . . . . . .9

USING FRONT A/V INPUT JACKS . . . . . . . . .10

C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .21

C TV OPERATION AND SETTINGS . . . . . . . . .10

WATCHING A TV PROGRAM . . . . . . . . . . . .10

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .11

GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .11

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .11

WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .11

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .12

CLOSED CAPTION SYSTEM . . . . . . . . . . . .12

CHANNEL SET UP . . . . . . . . . . . . . . . . . . . .12

CLOCK SET UP (AUTO / MANUAL) . . . . . .13

DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .15

MENU LANGUAGE . . . . . . . . . . . . . . . . . . . .15

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .16

NORMAL RECORDING . . . . . . . . . . . . . . . . .21

SKIPPING UNWANTED SCENES DURING

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .21

OTR (One Touch Recording) . . . . . . . . . . . . . .22

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . . . . . . . . . . .22

C TIMER RECORDING . . . . . . . . . . . . . . . . . . .23

AUTOMATIC TIMER RECORDING . . . . . . .23

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .24

C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25

C CABLE CHANNEL DESIGNATIONS . . . . . .25

C TROUBLESHOOTING GUIDE . . . . . . . . . . .26

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .27

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

C VIDEO CASSETTE . . . . . . . . . . . . . . . . . . . . .17

INDICE

CONTROLES DE OPERACIÓN Y

AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . .30

IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . .31

REPRODUCCION NORMAL . . . . . . . . . . . . .31

GRABACIÓN NORMAL . . . . . . . . . . . . . . . . .31

SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28

C PREPARACIÓN PARA LA UTILIZACIÓN . . .30

CONEXIONES DE ANTENA/CABLE . . . . . . . .30

C FUNCIONES Y AJUSTES . . . . . . . . . . . . . . . .30

PARA MIRAR UN PROGRAMA DE TV . . . . . . .30

A NOTE ABOUT RECYCLING

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

- 5 -

FEATURES

Infrared remote control

Trilingual on screen menu display selectable in

English, Spanish or French

Zero Return–The tape returns to counter of

•

0:00:00 by rewinding or fast forwarding.

Still–Freeze the picture at any time, for close view-

ing of a particular scene. Only tapes recorded in

SLP mode will show a fairly clear picture.

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

Time search–Let you set the unit to advance the

tape by entering the desired playback time you

want to skip.

OTR (One Touch Recording)–Instant timed

recording from 30 to 480 minutes is possible at the

push of the REC/OTR button.

1 Year, 8 events (including Daily and Weekly)

Timer Recording–The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts and the Weekly timer allows recording to be

made once a week up to the end of the tape.

Real time counter–This shows the elapsed record-

ing or playback time in hours, minutes and sec-

onds. The “–” indication will appear when the tape

is rewound further than the tape counter position

“0:00:00”.

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–(A converter may

be necessary to view scrambled cable channels.)

Auto Clock Setting–Allows you to set the clock

function from a PBS broadcast station.

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Game mode–Automatically sets external input

mode and allows unit display to be suitable for use

with video games.

•

Auto power on and off system–Automatically

turns on the unit when you insert the cassette, turns

off after auto-rewind, and ejects when the begin-

ning of the tape is reached.

Auto rewind when the end of a tape is reached

(This function doesn’t occur when using timer

recording.)

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed is avail-

able.

Auto return–After timer recording is finished, the

unit can return to the beginning of the recording.

Wake up/Sleep timer–Allows you to have the unit

automatically turn on or off at a desired time.

Timer Program Extension–Allow you to shift the

time schedule for automatic timer recording.

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

•

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video

heads as you insert or remove a cassette.

•

SUPPLIED ACCESSORIES

Owner’s Manual

Rod Antenna

2 AA Batteries

Remote Control Unit

(Supplied with 13"model only)

Owner's Manual

PART NO.

(N0150UD or

N0107UD )

PART NO. (0EMN00673,

0EMN01599 or 0EMN01755)

(1EMN20215)

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our

help line mentioned on the front page.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control. If you decide to use a universal remote control with this unit, please be aware

that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-

versal remote control.

•

- 6 -

OPERATING CONTROLS AND FUNCTIONS

This manual covers 13 and 19 . The operation of the two models are exactly the same except

the appearance. 19 model is illustrated in this manual.

- TV/VCR FRONT PANEL -

VIDEO

AUDIO

POWER

VOLUME

CHANNEL

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

EARPHONE

1 2

7 8 9

10 11

- REMOTE CONTROL -

7 STOP/EJECT

N button– Hit to stop the tape

motion. Hit in the stop mode to remove the

cassette from the unit.

8 REW b button– Hit to rewind the tape or to

view the picture rapidly in reverse during play-

back mode. (Rewind Search)

s button– (Remote control)

Hit to select a mode from the setting menu.

9 PLAY O button– Hit to start playback.

WAKE-UP

POWER

/SLEEP

EJECT

CHANNEL

RETURN

•

CHANNEL

VOLUME

button– (Remote control)

Hit to select a mode or figure from the setting

•

+100

menu.

DISPLAY

MUTE

10 F.FWD a button– Hit to rapidly advance the

tape or to view the picture rapidly in forward dur-

ing playback mode. (Forward Search)

B button– (Remote control)

PLAY

REW

F.FWD

STOP

Hit to determine your selection and proceed to

•

the next step in the setting menu.

11 REC/OTR button – Hit to start manual recording.

Hit repeatedly to start One Touch Recording

(OTR).

12 Record indicator– Flashes during recording.

Lights up in the stand-by mode for Timer

Recording.

SPEED PAUSE/STILL

RECORD

T-PROG.

CLEAR

GAME

TIME SEARCH

COUNTER

RESET

1 VIDEO input jack– Connect to the Video output

jack of a video camera or VCR.

2 AUDIO input jack– Connect to the Audio output

jack of an audio equipment, video camera or

VCR.

13 EARPHONE jack– Connects to earphones (not

supplied) for personal listening. The size of jack

is 1/8" (3.5mm) monaural.

14 Cassette compartment

15 Number buttons– Press to select desired chan-

nels for viewing or recording. To select a single-

digit channel, hit [0] first and then [1] to [9].

+100 button– When selecting cable channels

which are higher than 99, hit this button first,

then press the last two digits. (To select channel

125, first hit [+100] button then hit [2] and [5].)

16 MENU button– Hit to enter or exit the setting

menu.

3 POWER button– Hit to turn the unit on and off.

Hit to activate timer recording.

4 VOLUME

buttons– Adjust the volume level.

buttons– Press to select the

5 CHANNEL

desired channels for viewing or recording.

TRACKING function– Press to minimize video

‘noise’ (lines or dots on screen) during playback

mode. (Refer to page 18.)

6 Remote Sensor Window– Receives the infrared

signals from the remote control.

- 7 -

- REAR VIEW -

ANT.

17 DISPLAY button– Hit to display the counter or

the current channel number and current time on

the TV screen. (Refer to page 25.)

23 TIME SEARCH button– Hit to activate Time

Search mode.

24 PAUSE/STILL F button– Hit to temporarily stop

the tape during the recording or to view a still pic-

ture during playback.

18 STOP button– Hit to stop the tape motion.

button– (Remote control)

25 MUTE button– Hit to mute the sound. Hit it again

to restore the sound.

Hit to select a mode or figure from

the setting menu.

•

26 CHANNEL RETURN button– Hit to go back to

the previously viewed channel. Hit again to return

to the present channel.

27 EJECT A button– Hit in the stop mode to remove

the cassette from the unit.

28 WAKE-UP/SLEEP button– Sets the Wake up or

Sleep Timer. (Refer to page 11 or 12.)

29 Power cord– Connect to a standard AC outlet

(120V/60Hz). (Refer to page 10.)

30 ANT(ENNA). jack– Connect to an antenna, cable

system or satellite system. (Refer to page 9.)

19 RECORD button– Hit to start manual recording.

20 SPEED button– Hit to choose the desired record-

ing speed:SP/SLP.

21 T-PROG. CLEAR button– Hit to cancel a setting

of timer program. (Refer to page 24.)

COUNTER RESET button– Hit to reset counter to

0:00:00.

22 GAME button– Hit to set the Game mode and

external input mode at the same time. (Refer to

page 11.)

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

[BATTERY PRECAUTIONS]

Be sure to follow the correct polarity as indicated

in the battery compartment. Reversed batteries

may cause damage to the device.

•

Do not mix different types of batteries together

(e.g. Alkaline and Carbon-Zinc) or old batteries

with fresh ones.

•

3)Replace the cover.

If the device is not to be used for a long period of

time, remove the batteries to prevent damage or

injury from possible battery leakage.

•

Do not try to recharge batteries not intended to be

recharged; they can overheat and rupture.

•

- 8 -

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

Plug the incoming cable into the ANT. jack on the rear of the unit.

If your cable service supplies you with a converter box or if you use a

satellite system, connect the box with this unit as shown below.

Cable

TV signal

Antenna

ANT.

Incoming cable from home Antenna /

Cable Company (No Cable Box)

Rear of the unit

ANT.

Cable Box or

Satellite Box*

OUT

Incoming cable from Cable Company

or Satellite Antenna

*NOTE (DO NOT DISCONNECT FROM BOX)

Some cable TV systems use scrambled signals and

require a special converter to receive these channels.

Consult your local cable company.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding

system of the building as close to the point of cable entry as practical.

NOTE:

Rod Antenna Connection:

Rod Antenna

(Supplied)

Before plugging the antenna into the ANT. jack of the

unit, check that the pin is not bent. If it is bent, straighten

the pin as illustrated, then plug the pin into the ANT.

jack of the unit.

You can use the Rod Antenna

(Supplied) if incoming cable

is not available.

Bent pin

Cable Plug

ANT.

(Needs to be

straightened)

(Straight pin)

ANT.

For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack

before moving the unit.

- 9 -

USING FRONT A/V INPUT JACKS

When you watch a program recorded on another source (VCR or video camera), use the

AUDIO/VIDEO input jacks on the front of the unit.

AUX

Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO

jacks of this unit.

Then press [CHANNEL / ] until “AUX” appears on the screen.

VIDEO

AUDIO

POWER

VOLUME

CHANNEL

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

EARPHONE

ex.

VCR or video camera, etc.

[Front of the unit]

Audio cable

VIDEO

AUDIO

(OUT)

(IN)

(commercially available)

To the Audio output jack

Video cable (commercially available)

To the Video output jack

TV OPERATION AND SETTINGS

4 Adjust sound

WATCHING A TV PROGRAM

Press [VOLUME / ] to adjust

the volume.

1 Plug in the unit power cord

Plug the unit power cord into a standard

AC outlet.

VOLUME 20

Hit [MUTE] to instantly mute the

sound.

Hit it again to restore the previous sound level.

NOTE:

If any digits appear in the corner of the

•

screen, hit [POWER] without unplug-

TO WATCH CABLE OR SATELLITE

CHANNEL

ging the power cord.

If the unit is connected to a cable box or satellite

•

2 Turn on the unit

box, press [CHANNEL / ] to select CH3 or

CH4 according to the output channel setting of the

device and select desired channel on that device.

Hit [POWER] to turn on the unit.

3 Select the channel number

Press [CHANNEL / ] or the Number buttons to

TO WATCH EXTERNAL INPUT

select your desired channel number.

Note for using the Number buttons:

When an external equipment is connected to the

•

¡You must precede single-digit channel numbers

with a zero (for example: 02, 03, 04 and so on).

¡When selecting cable channels which are higher

than 99, hit [+100] first, then press the last two

digits. (Example: to select channel 125, first hit

[+100] then hit [2] and [5].)

front AUDIO/VIDEO input jacks, press [CHAN-

NEL / ] repeatedly until “AUX” appears on

the screen.

- 10 -

TO CANCEL THE GAME MODE

Press [GAME] or [CHANNEL / ] on the remote

control.

PICTURE CONTROL

The unit’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a more natural looking image.

NOTE:

When setting the Picture Control, the Game mode

will be cancelled.

Make sure ...

The unit power must be turned on.

DEGAUSSING

This television has a degaussing circuit that will clear

up color errors on the TV screen that are caused by

any excess magnetism which happens to get too close

to the TV. This circuit is designed to operate once

when the set is first plugged in. If minor color errors

are seen in some locations on the screen, please

unplug the TV for approximately 30 minutes. When

the TV is plugged back in, the degaussing circuit will

operate once to clear them up. Repeat this procedure

any time the TV screen is accidentally magnetized or

when the TV is moved or relocated.

•

– M E N U –

1 Select “PICTURE CONTROL”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Hit [MENU] on the remote control.

Press [PLAY/ ] or [STOP/ ] to

point to “PICTURE CONTROL”.

Then, hit [F.FWD/B].

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

WAKE UP TIMER

The Wake Up Timer function turns on the unit

2 Select item you want to adjust

without using [POWER] after a desired period of

Press [PLAY/ ] or [STOP/ ]

until desired control is displayed.

BRIGHT

time.

NOTES:

Use the remote control for this procedure.

•

CONTRAST

COLOR

TINT

SHARPNESS

BRIGHT

Clock must be set to the correct time before setting

•

–

P +

the timer.

If you want to select [TAPE], you must insert a

•

cassette tape in the unit. The tape will start

playback automatically on your desired time.

3 Adjust the picture control

1 Call up “WAKE-UP TIMER” setting

Hit [WAKE-UP/SLEEP] once, and

confirm “ON/OFF” is pointed.

Press [REW/s] or [F.FWD/B]

until “ON” appears.

Press [REW/s] or [F.FWD/B] to adjust to your

desired level within 5 seconds.

REW/s

to decrease

brightness

to decrease

contrast

F.FWD/B

to increase

brightness

to increase

contrast

WAKE UP B ON/OFF

[ON]

[TV]

[12:00AM]

TIMER

TV/TAPE

TIME

BRIGHT

CONTRAST

2 Select “TV” or “TAPE”

Press [PLAY/ ] or [STOP/ ]

until to point to “TV/TAPE”.

Press [REW/s] or [F.FWD/B],

and select [TV] or [TAPE].

COLOR

TINT

to pale

to brilliant

to purple

to green

to clear

WAKE UP

TIMER

ON/OFF

B TV/TAPE

TIME

[ON]

[TV]

[12:00AM]

SHARPNESS to soft

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

•

3 Set wake up time

Press [PLAY/ ] or [STOP/ ] until

GAME MODE

This function enables you to decrease the TV screen

contrast and making it suitable for use with a video

game.

NOTE: This function CANNOT be set during

recording.

to point to “TIME”.

Press [REW/s] or [F.FWD/B]

until your desired wake up time

appears.

WAKE UP

TIMER

ON/OFF

TV/TAPE

B TIME

[ON]

[TV]

[12:00AM]

Each additional press will increase

(or decrease) the time by 10

minutes.

Hit [GAME] on the remote control.

GAME

“GAME” appears on the screen.

4 Exit the Wake Up Timer setting

Hit [MENU] to return to TV mode.

When you hit [GAME];

The unit comes on automatically

•

if it is off.

TO CANCEL THE WAKE UP TIMER

Select [OFF] at step 1.

The unit will be in external input

•

mode automatically.

- 11 -

Make sure ...

•

SLEEP TIMER

The unit must be turned on.

The Sleep Timer function turns off the unit without

using [POWER] after a desired period of time.

NOTE:

– M E N U –

1 Select “CAPTION”

Hit [MENU].

Press [PLAY/ ] or [STOP/ ] to

point to “CAPTION”.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

This function does not work during Recording

•

V-CHIP SET UP

mode.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

1 Call up “SLEEP TIMER” setting

Hit [WAKE-UP/SLEEP] repeatedly so that “SLEEP

TIMER” appears.

2 Select your desired caption menu

– M E N U –

]

Press [REW/ ] or [F.FWD/

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

until your desired caption menu

appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

2 Set sleep time

Press [PLAY/ ], [STOP/ ],

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

[REW/ ] or [F.FWD/ ] until

your desired sleep time appears.

Each additional pressing will

increase the time by 30 minutes up

to 120.

TIME SEARCH

SLEEP TIMER [2:00]

3 Exit the caption setting mode

Hit [MENU] to return to TV mode.

NOTE:

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

Hit [MENU] to exit the Sleep Timer setting.

TO CANCEL THE SLEEP TIMER

•

Hit [WAKE-UP/SLEEP] until “SLEEP TIMER”

appears.

Press [PLAY/ ], [STOP/ ], [REW/s] or

TO CANCEL THE CLOSED CAPTION

SYSTEM

[F.FWD/B] until [OFF] appears.

Repeat steps 1 to 2 and select [OFF] using

[REW/ ] or [F.FWD/ ]. Then hit [MENU] to

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

return to TV mode.

CHANNEL SET UP

CAPTION mode: You can watch dramas, movies and

news while captioning the dialogues and the contents

of news.

Make sure ...

•

The unit must be turned on.

TEXT mode: You can watch half screen text informa-

tion if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is usually

used for a second language if available.

NOTES:

AUTO CHANNEL PROGRAMMING

As the initial setting, this unit has memorized all

channels, including the ones not available in your

area. This feature automatically puts only available

channels into the memory.

Not all programs are broadcast with closed cap-

•

tions. Your unit is designed to provide error free

closed captions from high quality antenna, cable

and VCR signals. Conversely, poor quality signals

are likely to result in caption errors or no captions

at all. Common signal conditions which may cause

caption errors are listed below:

1 Select “CHANNEL SET UP”

– M E N U –

Hit [MENU].

TIMER PROGRAMMING

PICTURE CONTROL

Press [PLAY/ ] or [STOP/ ] to

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

point to “CHANNEL SET UP”,

then hit [F.FWD/ ].

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Automobile ignition noise

•

Electric motor brush noise

•

Weak snowy reception on TV screen

•

– CHANNEL SET UP –

2 Begin channel scanning

Multiplex signal reception displaying picture

•

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

Press [PLAY/ ] or [STOP/ ] to

point to “AUTO CH PROGRAM-

MING”, then hit [F.FWD/B].

The tuner scans and memorizes all

the active channels in your area.

ghosts or airplane flutter.

Playback of poorly recorded or worn VCR tapes.

•

If the unit displays a black box on

•

the TV screen, this means that the

unit is set to the TEXT mode. To

clear screen, select [CAPTION1],

[CAPTION2] or [OFF].

- 12 -

5 Exit the channel setup mode

Hit [MENU] to returns to TV mode.

NOTE:

3 After scanning

The tuner stops on the lowest memorized channel.

To confirm that channel(s) has been deleted or

•

NOTES:

added, press [CHANNEL / ].

If there is no TV signal input, “NO TV SIGNALS”

•

will appear on the display after the completion of

channel scanning.

The unit may recognize TV channels to be CATV

CLOCK SET UP

•

channels if reception condition is poor. In this case,

check the antenna connection and try “AUTO CH

PROGRAMMING” again when reception condi-

tions are better.

(AUTO / MANUAL)

The unit clock must be set correctly so that VCR

timer recording is possible. It is suggested that the

clock be set manually when first setting up the unit,

then set to [ON] the auto clock setting which will

periodically correct the setting if necessary.

NOTE:

Channel memory programming is NOT neces-

•

sary when connected to a cable box or satellite

box. Just select the channel for the cable box or

satellite input (ex. CH3) on the unit, then select

your desired channel on the cable box or satel-

lite box.

If you cannot receive a station with time signals,

auto clock setting cannot be performed. Use manu-

al setting only.

•

ADDING/DELETING CHANNELS

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

MANUAL CLOCK SETTING

Make sure ...

The unit must be turned on.

•

In the example below, the clock is to be set to:

DATE

May 5th, 2005

1 Select “CHANNEL SET UP”

– M E N U –

SETTING TIME 5:40PM

TIMER PROGRAMMING

Hit [MENU].

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press [PLAY/ ] or [STOP/ ] to

point to “CHANNEL SET UP”,

then hit [F.FWD/B].

1 Select “SETTING CLOCK”

– M E N U –

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Hit [MENU].

TIME SEARCH

Press [PLAY/ ] or [STOP/ ] to

point to “SETTING CLOCK”, then

hit [F.FWD/B].

ZERO RETURN

TIME SEARCH

2 Select “ADD/DELETE CH”

– CHANNEL SET UP –

Press [PLAY/ ] or [STOP/ ] to

point to “ADD/DELETE CH”, then

hit [F.FWD/B].

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

2 Select “MANUAL CLOCK SET”

– SETTING CLOCK –

Press [PLAY/ ] or [STOP/ ] to

point to “MANUAL CLOCK SET”,

then hit [F.FWD/B].

AUTO CLOCK

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

[ 02 ]

[OFF]

3 Enter the desired channel number

Press [PLAY/ ] or [STOP/ ] or

the Number buttons until your

desired channel number appears.

(You can also press [CHANNEL

3 Select the month

– MANUAL CLOCK SET –

MONTH DAY YEAR

Press [PLAY/ ] or [STOP/ ] until

your desired month appears.

(Example: May → “05”)

ADD / DELETE

/ ] to enter it.)

You must precede single-digit

channel numbers with a zero (Example: 02 ... 09).

When selecting cable channels which are higher

than 99, hit [+100] first, then press the last two

digits. (Example: to select channel 125, first hit

[+100] then hit [2] and [5].)

0 5

– – – – – – – – –

•

HOUR

– –

MINUTE

– – – –

Then hit [F.FWD/ ].

•

– MANUAL CLOCK SET –

MONTH DAY YEAR

4 Select the day

Press [PLAY/ ] or [STOP/ ]

until your desired day appears.

(Example: 5th → “05”)

0 5

0 5 – – – – – – –

4 Delete (or add) it from (or into) memory

HOUR

– –

MINUTE

– – – –

Press [REW/ ] or [F.FWD/ ]. The channel number

Then hit [F.FWD/B].

changes to light red. The channel is deleted from memory.

To delete another channel, repeat steps 3 to 4.

•

5 Select the year

– MANUAL CLOCK SET –

MONTH DAY YEAR

If you press [REW/ ] or [F.FWD/ ] again, the

•

Press [PLAY/ ] or [STOP/ ]

until your desired year appears.

(Example: “2005”)

channel is memorized again.

0 5

0 5 THU 2 0 0 5

Added channel: Light blue

Deleted channel: Light red

HOUR

– –

MINUTE

– – – –

Then hit [F.FWD/ ].

- 13 -

– M E N U –

6 Select the hour

1 Select “SETTING CLOCK”

– MANUAL CLOCK SET –

MONTH DAY YEAR

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Press [PLAY/ ] or [STOP/ ]

until your desired hour appears.

(Example: “5”, “PM”)

Hit [MENU].

0 5

0 5 THU 2 0 0 5

Press [PLAY/ ] or [STOP/ ] to

select “SETTING CLOCK”, then

hit [F.FWD/B].

HOUR

0 5

MINUTE

– – PM

ZERO RETURN

TIME SEARCH

Then hit [F.FWD/B].

– SETTING CLOCK –

2 Set “AUTO CLOCK” to [ON]

Hit [F.FWD/B] until “AUTO

CLOCK [ON]” appears.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

Press [PLAY/ ] or [STOP/ ]

until the desired minute appears.

(Example: “40”)

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

0 5

0 5 THU 2 0 0 5

[OFF]

HOUR

0 5

MINUTE

4 0 PM

3 Begin “AUTO CLOCK CH SEARCH”

8 Start the clock

– SETTING CLOCK –

Hit [STOP/ ] to select “AUTO

Hit [MENU].

5:40 PM

AUTO CLOCK

[ON]

CLOCK CH SEARCH”.

Although seconds are not dis-

played, they begin counting from

00 when you hit [MENU]. Use this

feature to synchronize the clock

with the correct time.

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

B].

Then hit [F.FWD/

[OFF]

The unit begins searching for the

station which contains the auto

clock set signal. The search for a

signal may take up to 20 seconds

per channel.

When the search has ended, “_ _”

appears at the lower left of the

screen.

•

NOTE:

– AUTO CLOCK CH SEARCH –

When unplugging the AC cord or if there is a

power failure for more than 3 seconds, you may

have to reset the clock.

•

_ _

Write down the number(s) that

appear on the screen. They are the auto clock sta-

tion(s) in your area.

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 13. Hit

[MENU] to exit the screen.

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps 1 to 2 on page 13.

2)Select the item you want to change using

[REW/s] or [F.FWD/B].

3)Enter correct numbers using [PLAY

] or

[STOP

4)Hit [MENU] to start the clock.

NOTE:

During AUTO CLOCK CH SEARCH, the picture

may be distorted.

•

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press [REW/s] or [F.FWD/B] to turn [OFF] this

function. Then you can manually adjust the clock.

•

4 Enter the channel number that contains the

Automatic Clock Setting Signal

AUTOMATIC CLOCK SETTING

Make sure ...

Follow step 1 above to select “SET-

– SETTING CLOCK –

TING CLOCK” menu.

AUTO CLOCK

[ON]

The unit must be turned on.

Confirm the unit is receiving a RF (Radio

Frequency) signal from either an antenna or cable

•

Hit [STOP/ ] to select “AUTO

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[

45]

•

CLOCK CH”.

[OFF]

Press [REW/s] or [F.FWD/B]

until you locate Auto Clock Set sta-

tion number that you wrote down at step 3.

Hit [MENU] to exit the screen.

system connection using the ANT. jack on the rear

of the unit.

NOTES:

If a cable converter box is being used, make sure it

is powered on.

•

You must use the remote control to perform the

clock setting procedure.

If the unit is connected directly to a cable converter

box or satellite box, the local PBS station must be

selected on the cable box itself and the unit must

be set to the output channel of the cable converter

box or satellite box (usually channel 3 or 4), to be

able to set up or correct the clock automatically.

5 Turn off the unit

Once the unit is turned off, it will periodically check

and set the correct date and time.

•

- 14 -

DAYLIGHT-SAVING TIME

MENU LANGUAGE

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

1 Select “LANGUAGE”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

First Sunday of April : At 2 AM the clock imme-

Hit [MENU].

•

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

Press [PLAY/ ] or [STOP/ ] to

point to “LANGUAGE”.

TIME SEARCH

INDEX SEARCH

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

•

2 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”

Make sure ...

Press [REW/ ] or [F.FWD/ ] repeatedly to select

“ENGLISH”, “ESPAÑOL”= Spanish or

“FRANÇAIS”= French.

The unit must be turned on.

•

1 Select “SETTING CLOCK”

Hit [MENU].

Press [PLAY/ ] or [STOP/ ] to

point to “SETTING CLOCK”, then

hit [F.FWD/B].

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

3 Exit the Language mode

Hit [MENU] to turn to TV mode.

NOTES:

This function effects only the language on the

screen menu and not the audio source.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

•

If for some reason the menu is in Spanish or French,

•

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

hit [MENU], press [PLAY

] or [STOP

] to

Press [PLAY/ ] or [STOP/ ] to

– SETTING CLOCK –

point to “IDIOMA [ESPAÑOL]” or “LANGAGE

[FRANÇAIS]”, then hit [F.FWD/B] repeatedly to

select desired language, then hit [MENU].

point to “D.S.T.”, then press

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[REW/ ] or [F.FWD/ ] until

[ON]

“ON” appears.

3 Exit the Daylight-Saving Time mode

Hit [MENU] to return to TV mode.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps 1 to 2 and select [OFF] using

[REW/ ] or [F.FWD/ ].

- 15 -

Press [PLAY/ ] or [STOP/ ] to

select a rating with sub-ratings you

V-CHIP SET UP

TV–Y7

[BLOCK]

wish to block, then hit [F.FWD/

]

This feature enables parents to prevent their children

from watching inappropriate material on TV. When

you try to access a program which is blocked,

“PROTECTED PROGRAM by ...” message appears

on the TV screen.

twice.

Press [PLAY/ ] or [STOP/ ] to

select a sub-rating, then hit

[F.FWD/ ] to set it to [BLOCK]

TV–PG

[BLOCK]

or [VIEW].

[BLOCK]

V-CHIP SET UP

Make sure ...

•

The unit must be turned on.

Selection

TV-Y7

Rating Category Explanations

– M E N U –

1 Select “V-CHIP SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

Hit [MENU].

Fantasy Violence

TV-PG, TV-14, TV-MA

SETTING CLOCK

CHANNEL SET UP

Press [PLAY/ ] or [STOP/ ] to

select “V-CHIP SET UP”, then hit

[F.FWD/B].

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Suggestive Dialog (TV-PG, TV-14 only)

Coarse Language

Sexual Situation

2 Select the desired item

Violence

Press [PLAY/ ] or [STOP/ ] to select “TV RAT-

ING” or “MPAA RATING”, then hit [F.FWD/

B].

NOTE:

•

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

The blocked sub-ratings will

appear next to the rating category

in the “TV RATING” menu.

– V-CHIP SET UP –

(

)

[VIEW]

Step

[VIEW]

TV RATING

MPAA RATING

[BLOCK]

B Step

TV RATING SET UP

5 Exit the V-Chip setting mode

Press [MENU] to return to original mode.

NOTE:

PROTECTED PROGRAM

by TV-Y

To change the rating, the TV

must be turned to an unprotected

program. If “PROTECTED

•

Follow steps to in the “V-CHIP SET UP” section

above.

3 Blocking TV programs

PROGRAM by ...” appears on

the screen, please change the

channel to a station that is not protected.

Press [PLAY/ ] or [STOP/ ] to

select a rating that you wish to

block.

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

(

)

(

B ^{MPAA RATING SET UP}

Hit [F.FWD/B] repeatedly to set it

to [BLOCK] or [VIEW].

Follow steps to in the “V-CHIP SET UP”.

3 Select your desired item

Selection

TV-Y

TV-Y7

TV-G

Rating Category Explanations

Appropriate for all children

Appropriate for children seven and older

General Audience

Press [PLAY/ ] or [STOP/ ] to

[VIEW]

point to your desired item, then hit

PG–13

NC–17

[VIEW]

[BLOCK]

[F.FWD/ ] to select [BLOCK] or

[VIEW].

TV-PG

TV-14

Parental Guidance suggested.

Unsuitable for children under 14

Selection

Rating Category Explanations

General Audience

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

TV-MA Mature audience only

PG-13

NOTE:

When you select a rating and set it to [BLOCK],

•

the higher ratings will be blocked automatically.

The lower ratings will be available for viewing.

NC-17

When you set the lowest rating to [VIEW], all

•

Mature audience only

other ratings will automatically be available for

viewing.

When you select a rating and set it to [BLOCK],

the higher ratings will be blocked automatically.

The lower ratings will be available for viewing.

When you set the lowest rating to [VIEW], all

other ratings will automatically be available for

viewing.

•

4 Setting “Sub-Ratings”

When you select the ratings of TV-

Y7, TV-PG, TV-14 or TV-MA you

will have the option of setting sub

rating categories.

TV–Y

TV–Y7

TV–G

[VIEW]

(

)

[VIEW]

TV–PG (

TV–14

TV–MA(

)

(

4 Exit the V-Chip setting mode

Hit [MENU] to return to original mode.

- 16 -

VIDEO CASSETTE

This unit will operate with any cassette that has the

mark. For best results, we recommend the use of

high-quality tapes. Do not use poor quality or damaged tapes.

PRECAUTIONS

INSERTING A CASSETTE

Avoid moisture. Moisture condensation may occur

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the unit. The unit will

automatically turn on.

•

on the tape if it is moved from a cold place to a

warm place or vice versa. Before using a tape with

these conditions, to avoid damage of the tape and

your unit, wait until the tape has warmed to room

temperature and the moisture has evaporated.

Avoid extreme heat, high humidity and magnetic

fields.

Window

•

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

WRONG

CORRECT

•

TWO DIFFERENT TAPE SPEEDS

REMOVING A CASSETTE

1)In the stop mode, hit [STOP/EJECT

unit. The cassette will be ejected.

2)Pull the cassette out of the cassette compartment.

3)Store the cassette in its case as shown.

Before recording, select the tape speed from : SP mode

(Standard Play) or SLP mode (Super Long Play).

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each mode.

N] on the

Tape Speed

Type of tape

SP mode

Recording/Playback Time

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

NOTE:

You can play back a tape recorded in LP mode

(Long Play).

•

ERASE PREVENTION

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

If you decide to record on

the tape again, cover the

hole with plastic tape.

Plastic Tape

NOTE:

If the cassette without tab is inserted, playback will

automatically start.

•

- 17 -

PLAYBACK

NORMAL PLAYBACK

STILL PICTURE

Make sure ...

You can view a still picture on the TV screen during

playback (the Still mode). Hit [PAUSE/STILL

The unit must be turned on.

•

during playback. Only tapes recorded in the SLP

mode will show the least amount of lines. Hit

1 Insert a prerecorded tape

If the erase-prevention tab has been removed, the

unit will start playback automatically.

[PLAY/ ] to return to playback.

NOTES:

Usually there will be video “noise” lines (black

and white streaks or dots) on the screen. This is

normal.

•

2 To begin playback

PLAY

Hit [PLAY/ ].

If the tape was originally recorded in SP or LP

mode, the still picture will be black and white in

addition to the “noise” lines.

This is not a fault of the machine, but is a by-

product of the technology involved in producing

a unit with 2 video heads.

NOTE:

If any menu is activated on the

•

[PLAY/ ]

screen,

does not func-

tion. Hit [MENU] to exit the

menu. Then, hit

[PLAY/ ].

If the unit is left in the Pause mode for more than 5

minutes, the unit will automatically switch to the

stop mode.

•

3 To stop playback

STOP

Hit [STOP/ ].

NOISE CANCEL (in the Still mode)

This feature allows you to reposition or reduce the

noise lines of a still picture. Hit [PAUSE/STILL F]

so that the noise lines change position on the screen

so you can see the picture in its entirety without dis-

tracting noise lines.

TRACKING ADJUSTMENT

Tracking adjustment will be set automatically

(Digital Auto Tracking function) when you start

playback.

•

NOTE:

This feature can be activated ONLY when viewing

•

a tape recorded in the SLP mode. If the tape was

originally recorded in the SP or LP mode, the still

picture may revert to black and white in addition to

the “noise bars”. This is normal.

Noise lines (black and white streaks) may appear

on the playback picture when playing pre-recorded

tapes or tapes recorded on other VCR. If this

occurs, press [CHANNEL / ] until the streaks

disappear. To return to the Digital Auto Tracking

function, stop the tape once and start playback.

VERTICAL HOLD CONTROL

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

[CHANNEL / ].

NOTE:

If there are video noise lines on the screen, reposi-

tion or reduce them. Refer to “NOISE CANCEL”

above.

•

- 18 -

SPECIAL PLAYBACK

Make sure ...

AUTO REPEAT PLAYBACK

The unit must be turned on.

•

Insert a prerecorded tape.

The unit has the auto repeat function that allows you to

•

repeat a tape indefinitely without hitting [PLAY/ ]

RENTAL PLAYBACK

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

1 Select “USER’S SET UP”

– M E N U –

1 Select “USER’S SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Hit [MENU].

– M E N U –

Hit [MENU].

TIMER PROGRAMMING

PICTURE CONTROL

Press [PLAY/ ] or [STOP/ ] to

point to “USER’S SET UP”, then

hit [F.FWD/B].

Press [PLAY/ ] or [STOP/ ] to

point to “USER’S SET UP”, then

hit [F.FWD/B].

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

2 Set “RENTAL” to [ON]

USER’S SET UP

Press [PLAY/ ] or [STOP/ ] to

point to “RENTAL”.

–

2 Select “ALL” or “BLANK”

USER’S SET UP

–

RENTAL

[ON]

[OFF]

Press [PLAY/ ] or [STOP/ ] to

point to “REPEAT PLAY”.

REPEAT PLAY

AUTO RETURN

Press [F.FWD/B] or [REW/s]

until [ON] appears.

RENTAL

[OFF]

[ALL]

[OFF]

REPEAT PLAY

AUTO RETURN

Press [REW/s] or [F.FWD/B]

repeatedly until your desired selec-

tion [ALL] or [BLANK] appears.

3 Exit the Rental setting

Hit [MENU] to return to the TV mode.

3 Exit the Repeat Play setting

Hit [MENU] to return to the TV mode.

4 Start playback

Hit [PLAY/ ] to start playback.

4 Start playback

“RENTAL PLAY B” appears.

Hit [PLAY/ ] to start the Repeat Play.

Once you select the Rental mode, it stays in effect

even after you turn off the unit.

•

“REPEAT PLAY B” appears.

Once you select the Repeat Play mode, it stays in

effect even after you turn off the unit.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

TO CANCEL THE RENTAL MODE

•

Repeat steps 1 to 2 and select [OFF] using

[REW/s] or [F.FWD/B]. Hit [MENU] to return to

TV mode.

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps 1 to 2 and select [OFF] using

[REW/s] or [F.FWD/B]. Hit [MENU] to return to

TV mode.

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

- 19 -

Make sure ...

TIME SEARCH

The unit must be turned on.

•

Insert a tape.

•

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply

by entering the exact amount of playback time you

want to skip.

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

NOTES:

Time Search can be set up to a maximum of 9

•

hours 50 minutes (9:50) by 10 minutes at a time.

In the example below: To watch a program before/

after 2 hour 50 minutes from the present position, in

either direction.

Zero Return WILL NOT work on a blank tape or

a blank portion of a tape.

•

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

1 Call up “TIME SEARCH”

TIME SEARCH

0 : 10

setting

Hit [TIME SEARCH].

2 Reset the counter to 0:00:00

Hit [COUNTER RESET] repeatedly.

3 Begin recording or playback

2 Enter your desired time

Press [RECORD] or [PLAY/ ].

Press [PLAY/ ] or [STOP/ ] until

your desired time appears. (Example:

“2:50” stands for 2 hours 50 min-

utes) You can also use

TIME SEARCH

2 : 50

Hit [STOP/L] when recording or playback is com-

pleted.

4 To activate “ZERO RETURN” mode

[TIME SEARCH].

If you wish to cancel the Time Search at this point,

hit [MENU].

Hit [MENU].

– M E N U –

Press [PLAY/ ] or [STOP/ ] to

point to “ZERO RETURN”, then

hit [F.FWD/B].

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

3 Begin Time Search

The counter will appear on the TV

screen.

The tape will automatically stop when the counter

returns to 0:00:00. (approx.)

ZERO RETURN

TIME SEARCH

By pressing [REW/s] or [F.FWD/B], the unit will

rewind or fast forward to the specified point.

The time counts down during the search. When the

display shows “0:00”, the tape will start playback

automatically.

PICTURE SEARCH

TO CANCEL DURING TIME SEARCH

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

Press [STOP/EJECT

N] on the unit or [STOP/ ]

This will delete the selected time.

1 Start Picture Search

During playback, press [REW/ ] or [F.FWD/ ] to

view at a high speed (in forward/reverse).

2 Change searching speed

Press [REW/ ] or [F.FWD/ ] again to view at

super high speed (in the LP/SLP modes only).

NOTE:

Tapes recorded in the SP or LP mode will normally

display a noise bar on the TV screen and the pic-

ture may revert to Black and White.

•

3 Return to normal speed

Hit [PLAY/ ].

- 20 -

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time will

not change on a blank tape or blank portions on the

tape.) The “–” indication will appear when the tape

has rewound further than “0:00:00” on the tape

counter.

When the end of a tape is reached during record-

ing, playback or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the unit will eject the tape and turn itself

off.

This function is operative when Repeat Play is set

to [OFF].

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

•

RECORDING

Make sure ...

The unit must be turned on.

Insert a cassette tape with its erase-prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTE:

This unit will ONLY record and view the same channel.

•

SKIPPING UNWANTED

NORMAL RECORDING

You can ONLY watch the same TV program that is

being recorded.

SCENES DURING RECORDING

PAUSE

Hit [PAUSE/STILL F] to tem-

porarily stop recording.

Press [PAUSE/STILL F] or

[RECORD] to resume recording.

NOTES:

1 Select the channel to be recorded

Press the Number buttons or

CH 10

[CHANNEL / ].

After 5 minutes, the unit will automatically switch

to the Recording mode to prevent tape damage.

•

NOTE:

If the unit is connected to a cable

box or satellite box, the unit must

be on CH3 or CH4, then the channel to be recorded

must be selected on the cable box or satellite box.

•

If Closed Caption mode is on, the On-Screen

Display will appear for 5 seconds, then disappear.

•

2 Select the tape speed

Hit [SPEED] to select the desired

tape speed (SP/ SLP).

REC

3 Begin recording

Hit [RECORD].

4 Stop recording

Hit [STOP/ ].

- 21 -

Time(s)

1 time

Display

Recording length

(normal recording)

OTR (One Touch Recording)

This function enables you to set a recording length

simply by hitting [REC/OTR] on the unit.

Make sure ...

2 times

3 times

0:30

1:00

30 minutes

60 minutes

The unit must be turned on.

Insert a cassette tape with its erase-prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

NOTES:

You cannot start OTR with the remote control.

Recording starts immediately when [REC/OTR]

is hit.

When [REC/OTR] is hit 18 times, the unit returns

to the Normal Recording mode.

•

17 times

8:00

480 minutes

•

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

You can make copies of video tapes made by friends

or relatives for your enjoyment.

•

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

•

To stop the OTR operation, hit [STOP/EJECT

]

Connect your unit and a source (playing) VCR using

the following diagram.

•

on the unit or on the remote control.

To show the remaining time, hit [DISPLAY] on

the remote control so that “OTR” appears on the

[This unit]

TV screen. (It will show up momentarily then dis-

appear.)

VIDEO

AUDIO

POWER

VOLUME

Recording stops when the display shows 0:00.

Please note that in the SLP mode maximum

recording time, assuming the tape is started at the

beginning, is 8 hours using T-160 (or 6 hours

using T-120).

•

If the tape runs out before the end time, the unit

will switch to the stop mode immediately, ejects

the tape and turns itself off.

Even if [POWER] is hit during OTR, the unit

continues recording.

•

[Ex: Source

VCR or camcorder]

AUDIO

Audio/Video cable

(not supplied)

OUT

VIDEO

1 Select the channel to be recorded

Press the Number buttons or [CHANNEL / ].

1)Insert a pre-recorded video cassette into the source

VCR or camcorder.

2)Insert a blank video cassette or one you want to

record over, into the unit’s cassette compartment.

3)Hit [SPEED] on remote control for the unit to

select the desired recording speed (SP/SLP).

NOTE:

If the unit is connected to a cable box or satellite

•

box, the unit must be on CH3 or CH4, then the

channel to be recorded is selected on the cable box

or satellite box.

4)Press [CHANNEL / ] on the unit until “AUX”

appears on the screen.

5)Hit [REC/OTR] on the unit.

6)Begin playback of the tape in the source VCR or

camcorder.

2 Select the tape speed

Hit [SPEED] to select the desired tape speed

(SP/SLP).

NOTE:

OTR (2 : 30)

3 Begin OTR

For best results during copying, use the front

•

Hit [REC/OTR] on the unit as

many times as needed. The record-

ing length will be determined by

panel controls whenever possible. The remote

control might affect the source VCR’s playback

operation.

the number of times you hit

7)To stop copying, hit [STOP/EJECT

unit, then stop the tape on the source VCR or cam-

corder.

N] on the

[REC/OTR]. Each time it is hit, the recording time

will be increased by 30 minutes up to 8 hours.

- 22 -

TIMER RECORDING

AUTOMATIC TIMER

2 Select your desired program position (1 to 8)

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press [PLAY/ ] or [STOP/ ] to

RECORDING

select the desired program position,

- - -/- - - - - -:- -

-:- - - -

You may set the unit to start and end a recording while

you are away. You can set 8 programs to record on

specific days, daily or weekly within a 1 year period.

In the example below, the timer is being set to record:

then hit [F.FWD/ ].

DATE:

July 4th, 2005

3 Set the channel number

SETTING TIME: from 7:30PM to 8:50PM

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press [PLAY/ ] or [STOP/ ] until

the desired channel number appears

(Example: CH61), then hit

CHANNEL:

TAPE SPEED:

Make sure ...

If a cable box or satellite box is connected with the

unit you will be limited to record only one channel,

and the channel selector on the unit must be select-

ed to the output channel of the boxes CH 3 or CH

4 and then the actual channel to be recorded must

be selected on the boxes.

CH61

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

[F.FWD/ ].

•

NOTE:

If the unit is connected to a cable

•

box or satellite box, the unit must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

Clock must be set to the correct time and date

before setting the timer.

The unit must be turned on to program it.

Insert a cassette tape with its erase-prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

The channel you want to record is properly set in

advance. (Refer to page 12.)

Avoid overlap of programs ...

•

4 Select once, every day or weekly recording

– TIMER PROGRAMMING –

For once recording :

•

CH DATE

BEGIN END

Hit [PLAY/ ] until the desired

- - -/- - - - - -:- -

61 7/04 MON -:- -

- - -/- - - - - -:- -

-:- - - -

date appears. (Example: “7/04”

for July 4th)

Then hit [F.FWD/

B].

•

For every day recording : To record a TV program at

the same time on the same channel

every day. (Example: Monday

through Sunday)

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

There is a chance that a program will not be record-

ed, when programs overlap;

Hit [STOP/ ] until “EVRY

The program with an earlier start has priority.

•

DAY” appears, then hit

Once the earliest program finishes, the overlapping

•

[F.FWD/ ].

programs will begin recording in sequence.

When the starting time is the same, the program set

– TIMER PROGRAMMING –

CH DATE BEGIN END

•

For weekly recording : To record a

TV program at the same time on the

same channel every week. (Example:

every Monday)

on the highest position in the program list has pri-

ority.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

The illustration below demonstrates the sequence

•

of recordings.

Hit [STOP/ ] until “EVRY” and

Program 1

Program 2

Program 3

10:00AM - 11:00AM

9:00AM - 10:00AM

9:30AM - 12:00PM

Recording Sequence

your desired day of the week

appear together, then hit [F.FWD/B].

– TIMER PROGRAMMING –

5 Set beginning hour

CH DATE

BEGIN END

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

Press [PLAY/ ] or [STOP/ ] until

- - -/- - - - - -:- -

-:- - - -

the desired hour appears.

61 7/04 MON 7:12^P

- - -/- - - - - -:- -

(Example: “ 7, PM” for 7:30PM)

9:30AM-12:00PM

Then hit [F.FWD/ ].

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

– TIMER PROGRAMMING –

CH DATE BEGIN END

6 Set beginning minute

Press [PLAY/ ] or [STOP/ ] until

- - -/- - - - - -:- -

-:- - - -

the desired minute appears.

1 Select “TIMER PROGRAMMING”

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

– M E N U –

(Example: “30” for 7:30PM)

Hit [MENU].

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

Then hit [F.FWD/ ].

Confirm “TIMER PROGRAM-

MING” is pointed by hitting

V-CHIP SET UP

– TIMER PROGRAMMING –

CH DATE BEGIN END

7 Set end hour

[PLAY/ ], then hit [F.FWD/ ].

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

If you have not yet set the clock,

“MANUAL CLOCK SET”

appears. If so, follow steps 3 to 8 on page 13 and

14. Then set the timer recording.

Press [PLAY/ ] or [STOP/ ] until

•

- - -/- - - - - -:- -

-:- - - -

8:30^PM- -

-:- - - -

TIME SEARCH

the desired hour appears.

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

(Example: “8, PM” for 8:50PM)

Then hit [F.FWD/ ].

- 23 -

4)Hit [POWER] to set automatic timer recording.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

– TIMER PROGRAMMING –

CH DATE BEGIN END

8 Set end minute

Press [PLAY/ ] or [STOP/ ]

until the desired minute appears.

(Example: “50” for 8:50PM)

- - -/- - - - - -:- -

-:- - - -

8:50^PM- -

-:- - - -

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

1)Hit [POWER].

2)If recording is in progress, hit [STOP/EJECT

] on

Then hit [F.FWD/ ].

the unit.

3)Repeat steps to on page 23 and select a pro-

9 Set the tape speed

– TIMER PROGRAMMING –

CH DATE BEGIN END

gram you want to cancel.

4)Hit [T-PROG. CLEAR].

Press [PLAY/ ] or [STOP/ ]

until the desired tape speed

appears. (Example: “SP”)

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

5)Hit [MENU] to return to TV mode.

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

TO CONFIRM THE TIMER SETTING

1)Hit [POWER] so that the Recording indicator

light goes off.

10 Finish setting the program

2)Hit [MENU].

Hit [F.FWD/ ] to complete setting.

3)Confirm “TIMER PROGRAMMING” is selected.

4)Hit [F.FWD/B]. The details of programs appear

on the TV screen.

To set another program, repeat steps 2 to 10.

•

Hit [MENU] to exit the menu.

•

5)Hit [MENU] to return to TV mode.

11 Set the timer

NOTES:

Hit [POWER] to set automatic timer recording. The

recording indicator lights up.

The display will not be turned on automatically

•

at the time the programmed recording begins.

You must turn off the unit to activate automatic

timer recording.

If power is not turned off and you continue watching

TV, “TIMER REC STANDBY” starts flashing on the

TV screen 2 minutes before the programmed start time.

If the erase-prevention tab is removed, the cassette

will be ejected when [POWER] is hit to off.

If the tape runs out before the end time, the unit

will switch to the stop mode immediately and

the tape will be ejected.

•

AUTO RETURN

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

•

TIMER PROGRAM EXTENSION

To shift the time schedule of an automatic timer recording.

1)Hit [POWER].

– M E N U –

1 Select “USER’S SET UP”

2)Repeat step on page 23.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

3)Hit [RECORD] and select the desired program

Hit [MENU].

using [PLAY/ ] or [STOP/ ].

Press [PLAY/ ] or [STOP/ ] to

4)Hit [RECORD] again.

point to “USER’S SET UP”, then

Each additional push will shift forward the begin/end

time for recording by 10 minutes. When the recording

is already in progress, each additional push will shift

forward the end time only. If you want to cancel while

setting, hit [PAUSE/STILL F] on the remote control.

The recording time returns to the original time.

NOTE:

hit [F.FWD/ ].

USER’S SET UP

–

2 Set “AUTO RETURN” to [ON]

Press [PLAY/ ] or [STOP/ ] to

RENTAL

[OFF]

[ON]

REPEAT PLAY

AUTO RETURN

point to “AUTO RETURN”, then

]

press [REW/ ] or [F.FWD/

until [ON] appears.

When you shift forward the time schedule during

recording, the recording speed will automatically

be set to the SLP mode.

•

3 Auto Return will begin

When all the timer recordings are completed, the unit

will rewind to the beginning of the recorded program(s).

NOTE:

5)Press [REW/ ] or [F.FWD/ ] to exit the setting

menu. Then hit [MENU] to return to original mode.

If you hit [POWER] while tape is rewinding, the

Auto Return will stop.

•

TO CORRECT A PROGRAM

While setting a program; hit [REW/s] to go

•

back one step and enter the correct numbers using

4 Watch the recorded program

[PLAY/ ] or [STOP/ ].

After setting a program;

1)Hit [POWER].

Hit [PLAY/ ].

•

TO CANCEL THE AUTO RETURN MODE

Repeat steps 1 to 2 and select [OFF] using

[REW/s] or [F.FWD/B].

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

2)Repeat steps 1 to 2 on page 23.

3)Hit [F.FWD/ ] (or hit [REW/ ] to go back one

step) until the part you want to correct begins flashing,

] or

then make the changes using [PLAY

[STOP/ ].

- 24 -

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, hit [DISPLAY]. Each time you hit [DIS-

PLAY], the TV screen will change as follows:

When the Closed Caption mode is OFF:

When the Closed Caption mode is ON:

Counter mode: After 5 seconds, only the counter

remains. To clear it, hit [DISPLAY].

Clock mode: After 5 seconds, only the clock and

the channel number remain. To clear them, hit

The On Screen Display disappear after 5 seconds.

This is true even if [MUTE] or [PAUSE/STILL

F] is pressed while recording.

•

[DISPLAY].

OFF mode

Clock/Counter mode

OFF mode Counter mode

Clock mode

STOP

5:40PM

CH2

STOP

5:40 PM

CH2

COUNT 0:12:34

After 5 seconds

5:40PM

CH2

COUNT 0:12:34

Counter

remains

Clock & Channel

remains

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

CATV channel

TV Display

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

CATV channel

TV Display

CATV channel

TV Display

W+55 W+56 W+57 W+58

91 92 93 94

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

CATV channel

TV Display

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 25 -

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your unit,

locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to

remedy the problem.

PROBLEM

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Make sure the power is turned on.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Let the unit program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Check for broken pin of the antenna cable.

Adjust volume control on remote control or main unit.

Hit [MUTE] to restore sound.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the unit’s clock is set correctly.

No power.

•

No picture or sound.

No picture or poor picture on

the unit.

•

No sound or poor sound.

•

Timer recording is not possible.

Cannot go into Record mode.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

Adjust tracking control for a better picture using [CHANNEL / ]

on the unit.

•

Playback picture is partially noisy.

•

No picture but the audio is OK in

playback.

No operation by infrared Remote

Control.

Video or color fades in and out

when making a copy of a video tape

Head cleaning may be necessary. Refer to “AUTO HEAD

CLEANING” on page 27.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

copy guard protection.

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the unit away from the appliances,

the unit can repair itself automatically. If you want to repair

immediately, unplug the power cord, then plug it in again 30 minutes

or so later. This automatically resets the unit.

•

Different color marks on screen.

•

CLOSED CAPTION PROBLEM

POSSIBLE REMEDY

Misspelling in captions

Error committed by the closed captioning production company.

Possible in a live broadcast. Not in case of a prerecorded program.

A few seconds of delay is common for live broadcast.

Display capacity may not exceed 220 words per minute. If a dialogue

exceeds that rate, selective editing is used to insure that the captions

remain up-to-date with the current TV screen dialogue.

•

Text is not shown in its entirety or

a delay occurs from what is being

said.

Captions scrambled with white

boxes

Caused by interferences of building, power lines, thunderstorms, etc.

No captions in a program which

must contain closed caption

The broadcast may use a time compression process to speed up the

program. The decoder cannot read the compressed information and

captions will be lost.

Possibility of a illegal copy or an erroneous copying process

accidentally performed by the fabricator.

•

No captions in a prerecorded

videotape which indicated closed

captions included.

Black box in the TV screen

You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or

Caption “OFF”.

•

- 26 -

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

CRT :

13 or 19 inch in-line gun, 90˚

deflection tube

NTSC-M

Video input level :

Audio input level :

0.5~2.0Vp-p

-15dBs

Television system :

Closed caption system :§15.119/FCC

Video S/N ratio : More than 46dB

Audio S/N ratio : More than 43dB

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

CATV

Rotary two-head

1/2 inch

OTHER SPECIFICATIONS

[ 13 inch model ]

Power requirement : AC 120V/60Hz

Power consumption : 60W

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

Dimensions :

H :15-3/8"(389mm)

W:14-1/2"(367mm)

D :14-7/8"(377mm)

23.1 lbs (10.5kg)

#2~#6

#7~#13

#14~#69

Weight :

[ 19 inch model ]

Power requirement : AC 120V/60Hz

Power consumption : 80W

VHF :

MID band :

SUPER band :

HYPER band :

Terminals

A5~A1, A~I

J~W

W+1~W+84

Dimensions :

H :19-1/2"(493mm)

W:19-3/8"(491mm)

D :18-3/4"(475mm)

43.0 lbs. (19.5kg)

Weight :

Antenna input :

VHF/UHF 75 ohms

unbalanced

RCA connector [ 1

1/8" monaural (3.5 mm)

Designs and specifications are subject to change

without notice.

If there is a discrepancy between languages, the

default language will be English.

•

Video input :

Audio input :

Earphone :

MAINTENANCE

If a streaky or snowy picture appears during play-

back, the video heads in your unit may need to be

cleaned.

1.Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line mentioned on the

front page, to locate an Authorized Service Center.

NOTES:

CABINET CLEANING

Wipe the front panel and other exterior surfaces of

the unit with a soft cloth immersed in lukewarm

water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the unit. Such chemicals may

cause damage and discoloration to the exposed sur-

faces.

Remember to read the instructions included with

the video head cleaner before use.

Clean video heads only when problems occur.

•

AUTO HEAD CLEANING

Automatically cleans video heads as you insert or

•

remove a cassette, so you can see a clear picture.

Playback picture may become blurred of interrupt-

•

SERVICING

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

Should your unit become inoperative, do not try to

•

correct the problem by yourself. There are no user-

serviceable parts inside. Turn off, unplug the power

cord and please call our help line mentioned on the

front page to locate an Authorized Service Center.

- 27 -

CONTROLES DE OPERACIÓN Y SUS FUNCIONES

Este manual sirve para los modelos de 13" y 19". A excepción de la apariencia, la operación de los dos modelos es exac-

tamente la misma. En este manual se muestra el modelo de 19".

NOTA:

No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un

mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el

número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del

mando a distancia universal.

- PANEL FRONTAL -

VIDEO

AUDIO

POWER

VOLUME

CHANNEL

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

EARPHONE

10 11

1 2

7 8 9

- MANDO A DISTANCIA -

X Y

4 Botones VOLUME / – Ajustan el nivel del

volumen.

X Y

5 Botones CHANNEL / – Presione para

WAKE-UP

seleccionar los canales deseados para ver o

grabar.

POWER

/SLEEP

EJECT

CHANNEL

RETURN

Función de seguimiento– Presione para min-

imizar el ruido de video (líneas o puntos en la

pantalla) durante la reproducción.

6 Ventanilla del sensor de mando a distan-

cia– Recibe las señales infrarrojas procedentes

del mando a distancia.

CHANNEL

VOLUME

+100

7 Botón STOP/EJECT P N – Presione para

parar el movimiento de la cinta. Presione en el

modo de parada para expulsar el casete de la

unidad.

DISPLAY

MUTE

PLAY

REW

F.FWD

8 Botón REW

– Presione para rebobinar la

STOP

cinta, o para ver la imagen en retroceso rápido

durante el modo de reproducción. (Búsqueda con

rebobinado)

SPEED PAUSE/STILL

RECORD

T-PROG.

CLEAR

GAME

TIME SEARCH

Botón

(Mando a distancia)

COUNTER

RESET

Presione para seleccionar un modo desde un

menú particular.

•

9 Botón PLAY O – Presione para iniciar la repro-

ducción.

Botón (Mando a distancia)

1 Toma de entrada VIDEO– Conectela a la toma

de salida de video de su videocámara u otra

videograbadora.

Presione para seleccionar un modo o cifra del

•

menú de ajustes.

10Botón F.FWD

– Presione para avanzar ráp-

2 Toma de entrada AUDIO– Conectela a la toma

de salida de audio de su equipo de audio,

videocámara u otra videograbadora.

3 Botón POWER– Presione para encender y apa-

gar la unidad. Presione para activar la grabación

con temporizador.

idamente la cinta, o para ver la imagen en avance

rápido durante el modo de reproducción.

(Búsqueda con avance rápido)

Botón B (Mando a distancia)

Presione para determinar su selección y vaya al

paso siguiente en el menú de ajustes.

•

- 28 -

- VISTA POSTERIOR -

ANT.

11 Botón REC/OTR– Presione para iniciar la

grabación manual. Presione repetidamente para

empezar la grabación instantánea (OTR).

12Indicador de grabación– Parpadea durante la

grabación.

24Botón PAUSE/STILL F– Presione para detener

temporalmente la cinta durante la grabación o

para ver una imagen fija durante la reproducción.

25Botón MUTE– Silencia el sonido. Presione de

nuevo para recuperar el sonido.

Se enciende en el modo de espera de la grabación

con temporizador.

13Toma EARPHONE– Para conectar los auricu-

lares (no suministrados) y escuchar en privado.

La toma es mono y tiene un tamaño de 1/8"

(3,5 mm).

26Botón CHANNEL RETURN– Presione para

volver al canal anterior. Presione para volver al

canal actual.

27Botón EJECT A– Presione en el modo de

parada para retirar el casete de la unidad.

28Botón WAKE-UP/SLEEP– Ajusta el tempo-

rizador para despertar/dormir.

14Compartimiento del casete

15Botones numéricos– Presione para selec-

cionar los canales deseados para ver ó grabar.

Para seleccionar canales del 1 al 9, presione

primero el botón [0] y después el botón [1] a [9].

Botón +100– Cuando seleccione canales de

televisión por cable cuyo número sea superior al

99, presione primero este botón, y después pre-

sione los dos últimos dígitos. (Para seleccionar el

canal 125, presione primero el botón [+100] y

luego [2] y [5].)

29Cable de alimentación– Conecte a la toma de

CA estándar (120V/60Hz).

30Toma ANT.– Conecte a una antena, sistema de

televisión por cable o sistéma de satélite.

16Botón MENU– Presione para entrar o salir del

menú de ajustes.

17Botón DISPLAY– Presione para visualizar el

contador actual o el número del canal actual y la

del televisor.

18Botón STOP– Presione para parar la cinta.

Botón - (Mando a distancia)

Presione para seleccionar un modo o cifra en el

menú numéricos de ajustes.

•

19Botón RECORD– Presione para iniciar la

grabación manual.

20Botón SPEED– Presione para elegir la veloci-

dad de grabación deseada: SP/SLP.

21Botón T-PROG. CLEAR– Presione para cance-

lar un programa de temporizador.

Botón COUNTER RESET– Presione para

reponer el contador a 0:00:00.

22Botón GAME– Presione para establecer modo

Game (juego) y el modo de entrada externa al

mismo tiempo.

23Botón TIME SEARCH– Presione para activar

el modo de búsqueda con tiempo.

- 29 -

PREPARACIÓN PARA LA UTILIZACIÓN

CONEXIONES DE ANTENA/CABLE

Antena

Señal deTV

por cable

Antena de varilla (Incluído)

Trasera de

la unidad

Cable entrante desde

Antena de Casa / Compañia

de Cable (Sin Caja de Cable)

(Caja de Cable o

ANT.

Caja de Satélite)

(SALIDA)

OUT

ANT.

(ENTRADA)

Cable entrante desde Compañia

de Cable o Antena de Satélite

FUNCIONES Y AJUSTES

PARA VER UNA ENTRADA EXTERNA

PARA MIRAR UN PROGRAMA DE TV

Cuando se conecta un equipo externo en las tomas

•

de entrada AUDIO/VIDEO frontales, presione

1 Enchufe el cable eléctrico

Enchufe el cable eléctrico de la unidad en un toma-

corriente de CA del hogar.

K L

[CHANNEL / ] repetidamente hasta que

aparezca "AUX" en la pantalla.

NOTA:

AJUSTE DEL RELOJ

AJUSTE MANUAL DEL RELOJ

Asegúrese ...

La unidad debe estar encendida.

En el siguiente ejemplo, el reloj debe estar en:

Si aparecen números en la esquina de la pantalla, pre-

•

sione [POWER] sin desenchufar el cable eléctrico.

2 Encienda la unidad

Presione [POWER] para encender la unidad.

•

3 Seleccione el número de canal

FECHA

HORA DE AJUSTE

5 de mayo, 2005

5:40PM

K L

Presione [CHANNEL / ] o los botones numéri-

cos para seleccionar su número de canal deseado.

Nota para el uso de los botones numéricos:

¡Debe colocar un cero antes de los números de canal

de una sola cifra (por ejemplo: 02, 03, 04, etc.).

1 Seleccione “AJUSTE RELOJ”

Presione [MENU].

Presione [PLAY/ ] o [STOP/ ] para seleccionar

Cuando seleccione canales de cable de más de 99, pre-

sione primero [+100] y después las dos últimas cifras.

(Ejemplo: para seleccionar el canal 125, primero pre-

sione [+100] y después presione [2] y [5].)

“AJUSTE RELOJ” y presione [F.FWD/ ].

2 Seleccione “AJUSTE MANUAL RELOJ”

Presione [PLAY/ ] o [STOP/ ] para seleccionar

“AJUSTE MANUAL RELOJ” y presione

4 Ajuste el sonido

[F.FWD/ ].

X Y

Presione [VOLUME / ] para ajustar el volumen.

Presione [MUTE] para silenciar instantáneamente el sonido.

Presione nuevamente para recuperar el nivel de

sonido anterior.

3 Seleccione el mes

Presione [PLAY/ ] o [STOP/ ] hasta que aparezca

el mes deseado. (Ejemplo: Mayo → “05”)

Presione [F.FWD/B].

PARA VER CANALES DE CABLE O

SATELITE

4 Seleccione el día

Si la unidad está conectada a una caja de cable o

•

K L

Presione [PLAY/ ] o [STOP/ ] hasta que aparezca

caja de satélite, presione [CHANNEL / ] para

el día deseado. (Ejemplo: 5º → “05”)

seleccionar CH3 o CH4 de acuerdo con el ajuste

de canal de salida del equipo y seleccione el canal

deseado en el equipo.

Presione [F.FWD/

B].

- 30 -

5 Seleccione el año

Presione [PLAY/ ] o [STOP/ ] hasta que aparezca

el año deseado. (Ejemplo: “2005”)

Presione [F.FWD/B].

REPRODUCCION NORMAL

Asegúrese ...

La unidad debe estar encendida.

•

6 Seleccione la hora

Presione [PLAY/ ] o [STOP/ ] hasta que aparezca

la hora deseada. (Ejemplo: “5”, “PM”)

Presione [F.FWD/B].

1 Inserte una cinta pregrabada.

Si la lengüeta para evitar el borrado está rota, la

unidad empezará a reproducir automáticamente.

7 Seleccione los minutos

2 Para empezar a reproducir

Presione [PLAY/ ] o [STOP/ ] hasta que aparez-

REPRODUCIR

Presione [PLAY/ ].

can los minutos deseados. (Ejemplo: “40”)

NOTA:

Si hay un menú activado en la

•

8 Haga funcionar el reloj

[PLAY/ ]

pantalla,

no funciona.

Presione [MENU].

Presione [MENU] para salir el

Aunque no aparezcan los segundos, empezará a con-

tar desde 00 cuando presione [MENU]. Utilice esta

característica para sincronizar el reloj con la hora real.

NOTA:

Cuando desenchufe el cable de CA o si hay un

corte eléctrico de más de 3 segundos, puede ser

necesario reajustar el reloj.

[PLAY/ ].

menú. Después presione

PARAR

3 Para parar la reproducción

Presione [STOP/ ].

•

GRABACIÓN NORMAL

SOLO puede ver el mismo programa de TV que está

grabando.

IDIOMA DEL MENÚ

1 Seleccione “LANGUAGE”

Presione [MENU].

Presione [PLAY/K] o [STOP/L] para seleccionar al

“LANGUAGE”.

1 Seleccione el canal a grabar

Presione los botones numéricos o

CA 10

K L

[CHANNEL / ].

NOTA:

Si la unidad está conectada a una

2 Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS”

Presione [REW/s] o [F.FWD/B] repetidamente

para seleccionar “ENGLISH” = inglés, “ESPAÑOL”

o “FRANÇAIS” = francés.

•

caja de cable o caja de satélite, la

unidad debe estar en el CH3 o CH4 y el canal a

grabar debe seleccionarse en la caja de cable o caja

de satélite.

3 Salga del modo de idioma

Presione [MENU] para volver al modo de TV.

NOTAS:

2 Seleccione la velocidad de la cinta

Presione [SPEED] para seleccionar

la velocidad deseada de la cinta

(SP/SLP).

Esta función afecta sólo el idioma en el menú de la

•

pantalla y no la fuente de audio.

Si por alguna razón, el menú está en francés, pre-

•

sione [MENU], presione [PLAY/K] o [STOP/L]

para seleccionar al “LANGAGE [FRANÇAIS]” y

presione [F.FWD/B] repetidamente para selec-

cionar el idioma deseado y presione [MENU].

GRABAR

3 Empiece a grabar

Presione [RECORD].

4 Pare la grabación

Presione [STOP/ ].

- 31 -

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or

workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR:

FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date

of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail

purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to

any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE

PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN

THE UNIT IS CARRIED-IN TO A FUNAI AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest Authorized Service Center or for general service inquries, please call or

write to the following:

FUNAI CORPORATION, INC.

SERVICE CENTER

19900 Van Ness Avenue, Torrance, CA 90501

Tel :1-800-968-3429

http://www.SylvaniaConsumerElectronics.com

Head Office: 100 North Street, Teterboro, NJ 07608

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia

1EMN20215

★★★★★

T5514UQ / T7514UQ

Shark Carpet Cleaner S3101UKM User Manual
Sharp MP3 Docking Station DK KP95P User Manual
Sharp Speaker System CPUSB50 User Manual
Sony Battery Charger AC VQ800 User Manual
Sony Ericsson Headphones HBV 100 User Manual
Sony MP3 Player CFD G30 User Manual
Sony Portable CD Player D E776CK User Manual
Sony Speaker XS 602E User Manual
Sylvania VCR SSV6003 User Manual
TANDBERG Flat Panel Television 6000MXP User Manual